A custom headboard from MEBLIX in Almaty is made to an individual measurement and 3D design in our own 600 m² workshop. We build soft and combined models for your bed and your wall, install them with our own crews and give a 24-month warranty under the contract. Measurement and the design are free.
A headboard is made for a specific bed and a specific wall, so an order starts with a measurement rather than a catalogue. Here is what you can order on its own and how we deal with uneven walls.
Can you order just the headboard if you already have a bed
Yes. We make the headboard separately from the bed: we measure your bed and wall, design the piece for them and install it without replacing your sleeping place. Your bed is the starting point. We record the width of the sleeping area, the height of the side rail and its position relative to the wall instead of forcing a standard catalogue size onto it. The free measurement and 3D design take one to two days, and at this stage you can see how the piece will sit on the frame and whether it closes the gap between the bed and the wall. As a direct manufacturer, we handle measurement, design, production and installation ourselves. If the bed does not stand flush with the wall, the measurement records the real gap, because the mounting depth depends on it. Otherwise the headboard would hang in the air or hit the skirting board.
Mounting a headboard on an uneven wall without gaps
During the measurement we check the wall at several points and plan the fitting in advance, so the piece sits without gaps even in a panel building where the wall surface is out of plane. We record vertical and horizontal deviation at five to seven points along the future headboard rather than along one average line. Based on these readings we design the mating part of the mount and, where needed, add a seating rail that follows the relief of the wall. Our own crews do the installation, so the geometry of the piece is checked during the trial assembly in the workshop, before anyone travels to your home. A deviation of up to several centimetres is not levelled with plaster. It is compensated by the mounting design and precise geometry based on the measurement.
A headboard for a non-standard bed size
We make headboards for non-standard bed widths and heights, taking the size from your actual sleeping place rather than from a standard range. You can also order one for a bed you have already bought elsewhere. We take the real dimensions and allow for the rail height and any protruding soft elements, so the headboard does not block access to drawers or get in the way of the bedside table. The height is set by how you use the bed: for reading sitting up, for a low bed, or for a headboard that runs the full height of the wall. The 3D design shows how the piece relates to your pillows and lamps. Non-standard widths are most common with upholstered beds that have soft side rails and with lift-up storage beds. There the free travel of the mechanism matters too.
Upholstery materials and filling for a soft headboard
The soft part is made of upholstery, filling and a frame. How these three combine decides how the piece will look a year from now and whether it is comfortable to lean on in bed.
Which fabric to choose for a soft headboard
We work with velour, matting, chenille and linen, as well as leather and faux leather. For each use we pick a dense fabric that keeps its shape and does not stretch over curves. Velour gives depth of colour and a pleasant surface, but it collects pile and needs dry cleaning. Matting and chenille are denser and handle daily wear in the back zone better. Linen breathes and suits light interiors, though creases show more on it. Leather and faux leather wipe clean with a damp cloth and fit minimalist bedrooms. For this kind of piece, abrasion resistance where your back rests matters more than softness to the touch. That is where fabric wears fastest, so decorative fabrics make sense on accent models, while a headboard you read against is better in a dense, hard-wearing cloth.
Filling and frame that keep the headboard from sagging
Inside the soft part we use a frame made from Egger and Kronospan boards and a foam-based filling, so the headboard keeps its shape and does not give way under weight. The board is the rigid base that the soft layer is fixed to, while Blum, Hettich and Boyard hardware handles the joints and fixings that stop the frame from working loose over time. Filling thickness is chosen for the purpose. On a reading model we make the soft layer denser so your back does not press into the hard base. On a decorative model it is thinner, for a crisp silhouette. A thin layer of filling on a rigid frame feels like a plank, and real comfort comes from a firm base combined with enough soft thickness.
Comparing upholstery options
Comparing upholstery options| Upholstery | How it behaves | Care | Best for |
|---|
| Velour | soft, holds its colour | dry cleaning, no abrasives | a bedroom focused on cosiness |
|---|
| Matting | dense, hard-wearing | easy to vacuum | daily leaning, reading |
|---|
| Chenille | textured, warm | gentle brushing | a family bedroom |
|---|
| Linen | breathable, natural texture | careful washing of covers | light interiors |
|---|
| Leather and faux leather | smooth, wipes clean easily | damp cloth | minimalism, easy care |
|---|
| Rattan | woven texture, light look | dry wiping | combined models |
|---|
Headboard designs for the way you use your bed
The design of a headboard decides whether reading in bed is comfortable, where a lamp can go and how well the piece fits the interior. Below we look at height, decoration and functional options.
How tall a headboard should be for reading and TV
We choose the height for how you use the bed. To support your back while reading or watching TV in bed, the soft part should reach shoulder level of a seated person. For bedrooms with lower ceilings a height of 100–120 cm from the floor works well. Rooms with high ceilings and a large bed suit 130–150 cm, and custom models often get an individual size when a standard height does not match the mattress. A headboard that is too low makes you stuff pillows behind your back, while one that is too high looks heavy and covers wall decor. That is why the height is measured from the mattress, not from the floor. Also note the sleeping surface height with the new mattress: a difference of 5–7 cm changes comfort more than any finish.
Shelves, niches and lighting in the headboard
We make models with shelves, niches and built-in lighting, which gives you space for a lamp, a book and a phone right by the bed. A shelf is planned to the depth of a book and the thickness of a lamp, and a niche to the socket and charging cable. The LED strip is set into a concealed profile so the diodes are not visible. They are designed together with the bed frame, or a shelf ends up above the pillows. Lighting and shelves are built into the 3D design from the start. Adding them to a finished piece later is difficult and would mean taking the soft part apart. We prepare the design within 1–2 days after the measurement, and it shows how the shelf relates to the mattress height and the sockets on the wall.
Carriage tufting, buttons and rattan
We make models with carriage tufting, decorative buttons and quilted stitching, as well as rattan pieces and combined designs. Carriage tufting creates deep diamond relief and packs the filling tightly. Checkerboard stitching looks softer and takes less labour. Rattan combined with a soft insert adds texture without overloading the bedroom. A large mesh reads well against light walls, a fine one against dark walls. Carriage tufting and buttons gather dust in the recesses, so for a bedroom where you lean on the headboard a lot it is worth choosing smooth upholstery or a mix of decoration and a practical fabric. We weave rattan in our own workshop and fit the pattern to the width of the piece.
Ordering bed headboards from measurement to installation
The order goes through clear stages: measurement, design, workshop production, installation and handover. At every step you see what is happening with your piece and approve the details before they become a finished product.
Measurement and 3D design before production starts
We come out for a free measurement and prepare a 3D design within 1–2 days, so you see the shape, height and upholstery of the future model before the workshop starts work. At the measurement, the technologist records the bed width, wall height and the position of sockets and protrusions, and checks how level the base is. How the piece sits against the wall without gaps depends on these dimensions. In the design you approve the height and width, the depth of the soft part, the tufting pattern and the type of mount. The 3D design is signed off before cutting, because changes made after parts have gone into the workshop mean remaking finished elements. So we settle every open question before a single board is cut, and the technologist checks that the chosen upholstery and mount suit your wall.
Production in our own workshop and trial assembly
We make our products in our own 600 m² workshop in Almaty, which handles cutting, edge banding, painting and a trial assembly before dispatch. The frame is assembled with Blum, Hettich and Boyard hardware, Egger and Kronospan boards are cut strictly to the approved design, and the soft part is filled and upholstered on site. Every piece goes through a trial assembly in the workshop: the craftsmen join the parts and check the geometry, the fit of the fixings and how even the upholstery seams are. This run catches mismatches before delivery, so there is no need to rework the structure during installation.
Installation by our own crews and the acceptance certificate
Our own crews install the piece, and we sign the acceptance certificate once installation is complete, so you accept the work when everything is already in place. The crew levels the wall mount, joins the structure to the bed, and checks that shelves and niches carry their load without bending and that the soft part does not bulge at the seams. The certificate records the result on site. You pay the remaining 50 % once the certificate is signed, and we work by bank transfer under a contract. On uneven walls the crew evens out the gap along the full length, so inspect the work from that angle at handover.
Lead times, warranty and headboard durability
Lead times and the warranty are what buyers check before paying. Here is what production time depends on, what the warranty covers and how payment works under the contract.
What production lead times depend on
Lead times depend on the item and the material, and the exact figures for each option are listed in the price list on this page. Urgent orders are possible too. We accept them and tell you in advance which operations can be sped up without losing quality. Production time is shaped by cutting Egger or Kronospan boards, edge banding, painting and the trial assembly in our 600 m² workshop. Rattan weaving and carriage tufting require manual work, so their cycle is longer than for smooth upholstery. Lead time is driven less by the size of the piece than by the material and finish: complex painting or weaving lengthens the cycle more than extra width does. If your moving date is already set, tell us at the measurement and we will schedule the operations around it.
Warranty and payment under the contract
We give a 24-month warranty on the product under the contract, and Blum hardware carries a 25-year manufacturer's guarantee. Payment is a 50 % advance with the balance after the acceptance certificate. We sign the certificate after installation, once you have checked the fit against the wall, how the mechanisms work and that there are no gaps. We work by bank transfer. Hettich and Boyard hardware is used on the same assemblies, but we state the manufacturer's guarantee term for Blum only. The warranty applies when the piece is installed according to the design, so any changes to the mounting or wall-hung elements are best agreed with us. Delivery within the city and up to 30 km is free for larger orders, and the threshold is shown on the Delivery and Payment page.
The bottom line on bed headboards
Below is what matters most for the result of your order. It helps you check your piece against the design before work starts and avoid remaking anything once it is finished.
What to check before you order
- Measurement and design: a headboard is made for a specific bed and wall, so exact dimensions and a 3D design matter more than picking from a catalogue.
- Uneven walls: gaps and irregularities are removed by fitting to the measurement, not by levelling the wall itself.
- Upholstery and filling: these two layers decide how the piece looks now and whether it keeps its shape a year later.
- Height and shelves: height, niches and lighting are planned at the design stage and cannot be changed after production.
- Contract: lead times depend on the material, while the warranty and payment terms are fixed in the contract before work begins.